Concrete cutting in Santa Fe Springs CA - clean openings cut in the right spot
Need a doorway, a trench for a pipe or a section of slab taken out? We find what's inside first, then cut it clean.
- Licensed and insured.
- Free on-site estimates.
- Expect a reply within 1 business day.
When do you need concrete cutting, and what goes into it?
Concrete cutting in Santa Fe Springs means sawing, breaking or coring through a slab or a wall to open a trench, make room for a door, drill a pipe hole or take out a damaged section. Done right, it removes only the concrete you meant to lose.
Most cutting calls start with some other job, like a plumber who needs a trench, a door going into a concrete wall, or a cracked piece of patio that has to come out without wrecking the rest. The price moves with how thick the concrete is, what's inside it and how much has to go. The schedule mostly turns on the prep, because a new opening in a structural wall or slab usually needs an engineer to design it before we cut, and any permit question gets settled before we book the crew. Your estimate gives you your own number in writing.
How do you know it's time to cut concrete?
A broken section you want out
A cracked or sunken piece of driveway or patio is often the only bad part, and a saw line around it lets you replace that piece without breaking up the rest. Left alone, water gets under the loose edges and the bad area tends to grow, so the cut gets bigger.
A leak or pipe under the slab
When a plumber needs to get under a floor or patio, a sawed trench leaves straight edges that patch flat, where a hammer leaves ragged ones that rarely look right. Waiting on a leak lets water keep washing out the dirt the slab sits on.
New work meeting old concrete
A patio extension, a wider drive or a new door through a concrete wall all need a clean edge where the new part starts. Without one, the seam between old and new is where cracks and lifting usually show up first.
Concrete cutting the way we do it, from scan to cleanup
Before we cut anything, we find out what's inside the slab. A post-tensioned slab has steel cables run through it, pulled tight and anchored at the edge, and cutting one lets that force go all at once, so the strand can whip or burst out of the slab edge and hurt someone, and the slab loses part of the squeeze it was designed around. If there's any chance your slab is built that way, we bring in a scanning company to find the cables and want an engineer to approve the opening before the saw comes out. Then we mark the cut, saw it wet so the dust stays down instead of drifting into your house, break out the piece, core any round holes and haul the concrete away.
Cutting usually sets up the next job. When a cracked section comes out of a drive, we can pour the replacement and tie it to the old concrete, and when the whole thing is past saving, concrete driveway building is the better place to spend the money. The same goes out back, where we cut a straight edge so new concrete patio construction meets the old slab clean.
Slab and wall sawing
Straight cuts through a floor, patio, driveway or wall, for trenches, doorways and taking out a damaged section. It suits any job where the edge left behind has to look good or take new concrete.
Core drilling
Round holes through a slab or wall for pipes, drains and conduit. It's the cleanest way to get a line through concrete because it takes out only the hole and leaves the slab around it sound.
Breaking and removal
Breaking out and hauling off concrete that's coming out for good, often after a saw line marks where to stop. It suits a whole slab or a big section where nothing new has to match the edge.
Get a written estimate for your concrete cut
Send the form and we'll get back to you within one business day. I come out myself, look at the slab and give you a free written estimate, with no obligation.
(562) 689-9662- Based in
- Santa Fe Springs, CA 90670
- Hours
- Mon–Fri: 6 AM–10 PM, Sat–Sun: 8 AM–10 PM
What happens when you call us about cutting concrete?
Here's how a cutting job runs from your side, from the first call to the walk-through at the end.
Call or send us a message
Call (562) 689-9662 or use the form, and I come out myself to look at the slab and hear what you want cut. Point me to the slab edge too, since that's where the first clue about cables usually shows.
Get your estimate in writing
You get a written estimate that spells out what's included and what isn't, so a scan or an engineer's review doesn't turn up later as a surprise. We also check what the city or county office for your address requires before anything gets scheduled.
We scan, mark and cut
Our crew does the work with me on site, once any scan and engineer's approval are in hand. The crew cuts to the marks we agreed on, so the opening lands where you planned it.
Walk the finished job together
When we're done, I walk the job with you and we look at the edges, the opening and the cleanup. If something isn't what we said, that's the time to tell me.
Why Santa Fe Springs homeowners call Santa Fe Springs Concrete for cutting
I come out to every job
I look at every job myself before we price it, and I'm on site with the crew when the saw runs. You're not explaining your slab to one person and hoping it reaches another.
Working concrete since 2023
I learned the trade on other people's crews and started this business in 2023, mostly on flatwork, meaning the driveways, patios and slabs around a house. Knowing how a slab gets built tells you a lot about where the steel and the weak spots sit before you cut into one.
Licensed and insured in California
We're licensed and insured. That matters on a cutting job, because the saw is working near pipes, wires and steel nobody can see from the surface.
Based right here in Santa Fe Springs
Most of our calls come from homeowners around Santa Fe Springs, plus small property owners who need a lot, a wall or a slab done right. Being close means I can come look at your slab before you've had to guess at anything.
A cut can't be undone, so the planning is most of the job. Send us the details or call (562) 689-9662 and I'll come take a look.
Concrete cutting, permits and cleanup in Santa Fe Springs
In Santa Fe Springs, the Building and Safety Division wants permits in place before any project starts, and its list names new construction, remodeling, repairs and demolition but not concrete cutting by name, so whether your cut needs one isn't settled until you ask. The city's building permit guide gives a number you can call to find out. Before we schedule, we look up what applies at your address, and when a permit is needed we handle the paperwork with you and settle up front who calls for each inspection. When there is a permit, the city also has people name what gets reused, recycled or thrown out, and that plan has to be approved before the permit is issued, which matters here because broken concrete is most of what leaves a cutting job.
If the work reaches into the street side, like a utility trench, materials stored out front or cones in traffic, the city's Public Works Engineering Division handles those right-of-way permits through its online Permit Portal. We're based in Santa Fe Springs and work across the cities around it, and on jobs in Norwalk and Downey we see the same thing we see here, plenty of driveways and patios where one bad section or one plumbing trench is the whole problem.
Questions about concrete cutting in Santa Fe Springs
How much does concrete cutting cost in Santa Fe Springs?
Your price depends on your slab, so you get it from a written estimate after I've seen the job. Tight access and steel inside the concrete add time, and if the slab may be post-tensioned, the scanning company and the engineer belong in the budget too. Cutting out one bad section usually costs less than replacing the whole slab, which is why we look at that first.
How can I tell if my slab is post-tensioned?
Walk the edge of the slab and look for a line of small patched pockets spaced along it, because that's one sign the slab has cables anchored at its edge. Plenty of owners aren't sure either way, so if you see them or can't tell, send a photo and we'll plan for a scan.
How do I find out what's inside my concrete before cutting?
A professional scan is how you find out, since it can pick up cables, rebar, which is the steel bar that holds a slab together, conduit and other things buried in the concrete. Drawings and what you can see on the surface help, but on their own they aren't enough to clear a spot to cut.
What license covers concrete cutting work in California?
California's state license board has a concrete-related services class that covers concrete sawing, breaking and coring. Whoever you hire, ask what license they hold before any work starts.
How much deposit can a contractor ask for in California?
For a home improvement job, the state license board caps the down payment at $1,000, or less when the contract is small. Any other payments have to be listed in the contract and match work done or materials delivered.
How do I get ready for a concrete cutting estimate?
Take photos of the slab edge and the spot you want cut, and pull out the newest structural drawings or post-tensioning records you have. It also helps to mark the whole area that needs work and point out any patches or old repairs, so the scan covers all of it.
Related concrete work after the cut
If cracks run across most of your driveway, cutting out pieces moves the problem, and a new drive on a dug-out, packed base is usually the better fix.
A patio addition or a sunken corner starts with a clean saw line, then new concrete poured to meet it and drain away from the house.
Service areas for concrete cutting near Santa Fe Springs
Santa Fe Springs Concrete is based in Santa Fe Springs, California, and this site has pages for 12 cities we work in, including Whittier and Pico Rivera. If you don't see yours listed, just ask.
Santa Fe Springs, CA
Get your concrete cut planned right
Calling before the plumber or framer is booked gives any scan and engineer's sign-off time to fit their schedule instead of holding it up.